Fluke 6270A Скачать руководство пользователя страница 118

Страница: 118 / 144

6270A

Service Manual

112

Table 48. Troubleshooting (cont.)

Problem Probable

Cause

Action

Pressure Generation or Indication Problems

Product will not enter
control mode

Modules not
installed (PCM and
1+ modules)

Verify modules are properly installed. Door must be
closed and properly sensed as closed. Confirm door
status and pressure supply to PCM.

PMMs not fully
installed

Follow steps outlined in

Installation and Setup

to ensure

that all modules are properly installed.

No pressure
supply

Apply proper supply pressure.

Door not closed

Make sure the front panel is closed.

Internal door-close
sensor failed

Check the sensor. Send the Product to Fluke Calibration
for repair.

System in remote
operation mode

No pressure
measurement is
shown

Door not closed

Verify front panel is closed, verify the USB connection to
front panel is proper, verify Product is installed

PMM not installed

Install a PMM (see

Installation and Setup)

PCM not installed

Install a PCM (see

Installation and Setup)

Product does not
reach target pressure

Pressure supply
too low

Verify pressure supply, perform leak check.

Leak

Verify Test port is leak tight.

Valves require
service

Send the Product to Fluke Calibration for repair.

Target pressure
set higher than the
highest ranged
PMM.

Install a PMM with the appropriate range.

Slew Rate set to
zero

Increase slew rate.

While in measure
mode, pressure leaks

No supply
pressure

Provide supply pressure if not connected.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 118 / 144

Результаты поиска

Содержание 6270A

Отзывы: