Fluke 6270A Скачать руководство пользователя страница 7

Страница: 7 / 144

Introduction

The Fluke Calibration 6270A Pressure Controller/Calibrator (the Product)

precisely measures and controls pneumatic pressures up to 20 MPa (3000 psi).

Use the Product to calibrate, characterize, or test a wide variety of pressure

measurement devices that include transmitters, gauges, and switches.
The Product uses interchangeable Pressure Measurement Modules (PMMs) and

a Pressure Control Module (PCM) to regulate pressure output. The touchscreen

display features a multi-language user interface (UI). See

Instrument Setup Menu

in the

6270A Operators Manual

for more information.

This manual provides performance test, calibration adjustment, theory of

operation, troubleshooting, and repair procedures necessary to verify and

maintain Product performance.
The performance tests are based on the published 1-year specifications for the

Product. Fluke Calibration recommends the performance test as an acceptance

test when the Product is first received and later as a procedure to ensure that the

Product meets its published specifications. Fluke Calibration recommends a

1-year calibration cycle for the Product.
Use calibration adjustments to correct out-of-tolerance parameters so they meet

published specifications. If the Product fails the performance test, it is an

indication that the Product requires calibration adjustment and/or repair. While

calibration adjustment can be accomplished without removal of the covers, repair

requires access to the interior of the Product.
Environmental and warm up conditions required for the performance test and

calibration adjustments are stated at the beginning of each of the respective

sections.

Note

Repairs detailed in this manual are to the Modular-level only. Return
the Product to Fluke Calibration or take the Product to a local Fluke
Calibration Service Center for deeper-level repair.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 7 / 144

Результаты поиска

Содержание 6270A

Отзывы: