manualshive.com logo in svg

Fluke 6270A, Руководство по обслуживанию, Страница: 117 / 144

Поделиться
Скачать
Fluke 6270A Скачать руководство пользователя страница 117

 Pressure 

Controller/Calibrator 

 

Troubleshooting 

111 

 

To use a 2400 DWG: 

1.  Setup the 2400 DWG per the instructions in the 

2400 DWG Users Manual

. 

2.  Start COMPASS for Pressure and select the appropriate UUT and test 

definition for the PMM under test. 

3.  Create appropriate UUT and test definitions in COMPASS for Pressure with 

the pressures defined in the calibration matrices at the end of this manual. 
Pressure measurement command for sled: 
VAL? 
Pressure command for active module on the chassis: 
MEAS:PRES1? 
Each calibrated range requires a COMPASS for Pressure data (.dat) file to be 

saved in the approved COMPASS for Pressure directory under the 

Model>Serial Number

 of the UUT. The COMPASS for Pressure data file 

directory location is determined by the calibration laboratory. The default 

location is 

C:\dhi\COMPASS for Pressure\Data

.   

Troubleshooting  

Table 48 explains minor troubleshooting issues. For issues outside of the scope of this 

section, the Product may require service. See 

Contact Fluke Calibration. 

Table 48. Troubleshooting 

Problem Probable 

Cause 

Action 

Electrical Problems 

Product 
does not 
turn on 

Not plugged in 

Verify that the Product is plugged in and power is available.  

Power not available 

Check the fuse per instruction in this manual. 

Fuse blown 

Verify the main power switch is ON. 
Check the fan. If the fan is on or solenoid click is heard, see 
the “Display does not turn on” problem. 
If the fan is not on, have the power supply serviced. Verify 
internal power connections. 

Display 
does not 
turn on  

Chassis power issue 

Verify that power is supplied, see above. 

Screen saver is 
activated 

Verify power to front panel. 

 and 

should be lit. 

Power plug to front 
panel is loose 

Verify the 

 is in the ON state. 

Display panel failure 

If 

 is yellow, then push it to turn on display. 

Open front panel and verify the power plug is connected to the 
front panel. 

Display is 
on with 
graphics but 
no numbers 

USB interface to front 
panel is disconnected 

Open the front panel door, check the USB cable connection to 
the front panel. 

Reinstall the USB cable connection. 

Rear panel 
drivers not 
operating 

Loose connection 

Inspect the connection. 

Exceeded maximum 
power rating 

Allow internal fuse to cool and retry. Verify the rating of the 
external solenoids. 

Limit current of external solenoids. 

Содержание 6270A

















































































































































Отзывы:

Нет отзывов