Fluke 6270A Скачать руководство пользователя страница 45

Страница: 45 / 144

Pressure

Controller/Calibrator

Module Guide Rails

G- and B-Series Valves

Use the procedure below to repair, replace, or clean the G- or B-series valves or

associated parts. The G- and B-series valves are listed in Table 4.

Note

Valves can be replaced without removing the entire dock assembly.
However, instructions for complete removal are included here.

1.  Shut off the supply pressure and vent the system.
2.  Remove all pressure lines and fittings from the manifold.
3.  Use the procedures explained earlier to remove all PMMs and PCMs, top

panel, and COMM tray.
If the valves will be removed without completely removing the dock

assemblies, stop here. For complete removal of dock assemblies, also see

the sections

Manifold Replacement

and

PMM Dock Assembly

Valves come with coils and wires installed. The coils can be reused and only

replace the valve if the coil is still good. See Figure 20 and Table 3 for

wire/connector placement if installing new coil.

hxn226.eps

Figure 20. G and B Series Valves

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 45 / 144

Результаты поиска

Содержание 6270A

Отзывы: