Fluke 6270A Скачать руководство пользователя страница 122

Страница: 122 / 144

6270A

Service Manual

116

Remote Interface

The Remote Interface diagnostics menu provides information on remote

communication by monitoring the input and output communication. The menu

contains independent diagnostics for RS-232, USB, Ethernet, GPIB, and the

system bus communications.

RS-232

– Shows the Receive and Transmit data for this interface.

USB

– Shows the Receive and Transmit data for this interface.

Ethernet

– Shows the Receive and Transmit data for this interface.

GPIB

– Shows the Receive and Transmit data for this interface.

System Bus

– Shows the subsequent data for this interface.

•

Receive

•

Transmit

•

Fault

Contamination Prevention System (CPS)

The contamination prevention system (CPS) is a Product accessory used to

protect the Product from contamination from the UUT.

Note

Replace parts as required. See the Replaceable Parts section.

CPS Cleaning and Inspection

To clean and inspect the CPS filter assembly (see Figure 48):
1. Vent the Product to remove all pressure to the CPS.
2. Remove the hose from the quick connect



3. Remove the lower housing



from the upper housing



Turn the housing

counter clockwise to loosen it.

4. Pull straight out on the purge tube portion of the filter assembly



to remove

entire assembly from the upper housing.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 122 / 144

Результаты поиска

Содержание 6270A

Отзывы: