Fluke 6270A Скачать руководство пользователя страница 3

Страница: 3 / 144

Table of Contents

Title

Page

Introduction ............................................................................................ 1

Contact Fluke Calibration ...................................................................... 2

Safety Information ................................................................................. 2

Symbols ................................................................................................. 3

The Product Manual Set ........................................................................ 4

Specifications ........................................................................................ 4

Control Specifications ............................................................................ 6

Pressure Measurement Specifications .............................................. 6

PM200 Modules ................................................................................. 7

PM600 Modules ................................................................................. 8

Theory of Operation .............................................................................. 9

Overview ............................................................................................ 9

Accessories ....................................................................................... 9

Pneumatic and Electrical Configuration ............................................. 9

Pneumatic Interfaces ......................................................................... 11

Over Pressure Protection .................................................................. 11

Electrical ............................................................................................ 13

Module Connector ............................................................................. 14

PCA Overview ................................................................................... 15

Communications / Firmware .............................................................. 16

System Boot ...................................................................................... 17

Software Upgrades ................................................................................ 17

Maintenance .......................................................................................... 18

Access the Module Bay ..................................................................... 18

PMM and PCM Removal ................................................................... 19

Clean the Exterior .............................................................................. 21

Pressure Leakage Test (on-board diagnostics) ................................. 21

Fuse Replacement ............................................................................ 22

Manifold Replacement ....................................................................... 23

Repair and Replacement ....................................................................... 25

Feet and Tilt Stands .......................................................................... 25

Remove and Replace Handles .......................................................... 27

Top Panel .......................................................................................... 29

Module Guide Rails ............................................................................... 30

Communications Tray ........................................................................ 32

The CPU ............................................................................................ 33

PMM Dock Assembly ........................................................................ 35

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 3 / 144

Результаты поиска

Содержание 6270A

Отзывы: