Fluke 6270A Скачать руководство пользователя страница 39

Страница: 39 / 144

Pressure

Controller/Calibrator

Module Guide Rails

8. Use a #2 Phillips screwdriver to remove the two M3 x 6 screws



from the

COMM tray



and remove the tray from the chassis.

hxn207.eps

Figure 15. Remove the Communications Tray

The CPU

To remove the CPU, see Figure 16:
1.  Make sure the Product is off and disconnect the mains power cord.
2.  Shut off the supply pressure and vent the system.
3.  Remove the top panel, see

Top Panel.

4. Remove the COMM tray. See

Communications Tray

5. Disconnect the system cable from CPU PCA J31



6. Disconnect the switch test cable from CPU PCA J1



7. Use a #2 Phillips screwdriver to remove the six M3 x 6 screws



8. Use a 7 mm nut driver to remove the two RS-232 connector jack screws



9. Use a 9/32 in nut driver to remove the two IEEE connector jack screws



10. Separate the CPU



from the COMM tray



Note

To avoid damage to the surface-mount components on the bottom
side of the PCA, use care when you separate the PCA from COMM
tray.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 39 / 144

Результаты поиска

Содержание 6270A

Отзывы: