manualshive.com logo in svg

Fluke 6270A, Руководство по обслуживанию, Страница: 142 / 144

Поделиться
Скачать
Fluke 6270A Скачать руководство пользователя страница 142

6270A 

Service Manual 

136 

Screw Torque 

The torque for the screws used in the Product are listed in Table 50. 

Table 50. Screw Torque 

Group Description 

Part 

Number 

Qty Function 

Torque  

N-m  (lb-in) 

Chassis 

SCREW, M3x0.5x25mm, 6-LOBE 
TORQ T10 Head 

4637695 6 

PLASTIC BEZEL TO FRONT PANEL 
SUPPORT 

1.7 (15) 

Chassis 

SCREW, M2x0.4x3mm, PAN HEAD 
PHILLIPS, STEEL, ZINC-
CHROMATE 

2568619 4 

DISPLAY TO DISPLAY MOUNTING 
BRACKETS 

0.113 (1) 

Chassis 

SCREW, M3x0.5x10mm, PAN HEAD 
PHILLIPS, W/PLAIN & LOCK 
WASHERS 

4565518 4 

DISPLAY PCAP PCA TO PCA 
COVER 

0.57 (5) 

Chassis 

SCREW, M3x0.5x6mm, PAN HEAD 
PHILLIPS, W/PLAIN & LOCK 
WASHERS 

4556816 4 

DISPLAY MOUNTING BRACKETS 
TO PCA COVER 

0.57 (5) 

Chassis 

  

  

7 

DISPLAY DRIVER PCA TO PCA 
COVER 

0.57 (5) 

Chassis 

  

  

4 

DISPLAY PCAP PCA TO DISPLAY 
MOUNTING BRACKET 

0.57 (5) 

Chassis 

  

  

6 

SOLENOID DRIVER PCA TO 
INTERFACE BRACKET (PCM) 

0.57 (5) 

Chassis 

  

  

6 

SOLENOID DRIVER PCA TO 
INTERFACE BRACKET (PTM) 

0.57 (5) 

Chassis 

  

  

6 

COMM/PROCESSOR PCA TO 
COMMS TRAY 

0.57 (5) 

Chassis 

  

  

4 

CABLE TRACK TO CHASSIS 

0.57 (5) 

Chassis 

SCREW, M4x0.7x8mm, LOW HEAD 
SOCKET CAP, SST 

4427128 

20 

HANDLES & CAPS TO CHASSIS 

1.7 (15) 

Chassis 

SHOULDER SCREW, M5x0.8, 
SHOULDER DIA. 6 x 20 LONG, SST 

4406462 1 

FRONT PANEL LATCH TO FRONT 
PANEL SUPPORT 

2.8 (25) 

Chassis 

SCREW, M3x0.5x6mm, FLAT HEAD 
PHILLIPS 

3153213 2 

POWER ENTRY MODULE TO 
CHASSIS 

0.57 (5) 

Chassis 

  

  

7 

PCA COVER TO FRONT PANEL 
SHELL 

0.57 (5) 

Chassis 

SCREW, M3.5x0.6x8mm PAN HEAD 
PHILLIPS, BRIGHT ZINC PLATED 

4427287 

4 

POWER SUPPLY TO CHASSIS 

1.7 (15) 

Chassis 

  

  

2 

GROUND CABLE TO CHASSIS 
(CABLE TRACK) 

1.7 (15) 

Chassis 

NUT, NYLON INSERT, M3 

4398391 

2 

FAN TO CHASSIS 

1.13 (10) 

Chassis 

NUT, PLAIN, M3.5 

4398406 

2 

GROUND CABLES TO CHASSIS 

1.13 (10) 

Chassis 

SCREW, 5-14, .313, PAN, 
HEXALOBULAR, STEEL, BLACK, 
BLUNT PT 

1282984 

9 

KEYPAD PCA TO PLASTIC BEZEL 

0.57 (5) 

Chassis 

CONNECTOR ACC, MICRO-
RIBBON, SCREW LOCK KIT 

836585 2 

IEEE CONNECTOR TO COMMS 
TRAY 

0.57 (5) 

Chassis 

JACKSCREW DB9 

1610995 

2 

JACKSCREW FOR DB9 

0.57 (5) 

Chassis 

SCREW, M4x0.7x30mm, SOCKET 
HEAD CAP SST WITH NYLON 
PATCH 

4400701 

3 

PTM DOCK TO CHASSIS 

2.26 (20) 

Содержание 6270A

















































































































































Отзывы:

Нет отзывов