Fluke 6270A Скачать руководство пользователя страница 128

Страница: 128 / 144

6270A

Service Manual

122

Vent

Purge

hxn034.eps

Figure 52. CPS Assembly

Inspect and Replace the CPS valves

To inspect and replace the CPS valves, see Figure 53:
1. Separate the lower and upper housing from the chassis as described

previously.

2. Vent the controller to remove all pressure to the CPS.
3. Use a 9/16 inch socket or wrench to remove the retaining nut



for the valve

coil



4. Remove the coil from the valve base



5. Use a flat-head screwdriver to remove the valve stem



from the valve base

6. Ensure the O-ring



remains in the valve base and do not lose the valve

body



Note that the vent valve has a spacer that goes above the valve

body and must be in the vent valve assembly for proper operation.

7. Remove the valve body from the valve stem and inspect the sealing surface



for any contamination or damage.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 128 / 144

Результаты поиска

Содержание 6270A

Отзывы: