Fluke 6270A Скачать руководство пользователя страница 116

Страница: 116 / 144

6270A

Service Manual

110

Calibration with COMPASS for Pressure

See the other guidelines for calibration at the start of this main section. In

addition:

•

Use the As Found data file to determine the new C0 and C1 calibration

coefficients and calibration date.

•

Limit traffic in the area during calibration. Make sure that the calibration

bench is free from environmental disturbances such as:

drastic changes in pressure

temperature

humidity

air flow and vibration from start of calibration to finish.

•

Calibration must be done in the native operating mode of the PMM. The

native mode is the first letter of the range designation (A = absolute, BG or G

= gauge).

•

The Product must warm up according to equipment specifications.

•

Do not turn off or clear the UUT ZOFFSET. Calibration data is collected with

the zero stored in the module.

•

Gauge (G) and Bi-Directional Gauge (BG) UUTs must be zeroed before data

collection.

•

Absolute (A) UUTs are not zeroed before data collection.

To use a PG7000 Piston Gauge:

Set up the piston gauge per the instructions in the

PG7000 Users Manual

To use a FPG8601:

Set up the FPG and FPG tools per the instructions in the

FPG8601 Users

Manual

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 116 / 144

Результаты поиска

Содержание 6270A

Отзывы: