ESPEC LH-113 Скачать руководство пользователя страница 38

Страница: 38 / 110

Chapter 4 Operation

4. Lay the ends of the wet-bulb wick in the wick pan.

Wick pan

Align wick tail edge with

sensor tip.

Dry-bulb
temperature
sensor

Wet-bulb
temperature
sensor

Wet-bulb wick

Do not insert the sensor into the
bottom hole. The wick will not
drape at the correct height for
absorbing water.

4.10 How to set the wet-bulb wick 2

Wick Pan Water Level Check

(Not necessary with LU cabinet)

1. Check water in the wick pan is at the level shown in the below figure.

Wick Pan

Normally
about 8 mm

Fig. 4.11 Wick pan water level

2. It takes time to fill the wick pan with water.

3. If water level is low (high), slightly reposition the wick pan water

supplier higher (lower) on the back wall of the water circuit

compartment.

Water Tank Water Level Check

(Not necessary with LU cabinet)

Check water level in the water tank. If low, add water as explained in

"3.4 Water Level Check".

Procedure

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание LH-113















































































































Результаты поиска

Содержание LH-113

Отзывы:

ESPEC LH-113, Руководство пользователя, Страница: 38 / 110

Результаты поиска

Содержание LH-113

Отзывы: