ESPEC LH-113 Скачать руководство пользователя страница 31

Страница: 31 / 110

Chapter 3 Installation

To Check Water Level in the Humidifying Tray Water Level Regulator

Water level in the humidifying tray will depend on the water level in the

humidifying tray water level regulator.

The air circulator in the water circuit (heat exhaust) compartment

panel is dangerous. Before opening the compartment panel, set the

main power switch in the OFF position.

1. Detach the water circuit (heat exhaust) compartment panel.

2. Check water level in the humidifying tray water level regulator is

above the WATER LEVEL FOR HUMIDIFIER mark.

7mm

WATER LEVEL FOR
HUMIDIFIER mark

Nut

Humidifying tray
water level regulator

Humidifying tray

Water level sensor

Position adjusting screw

Fig. 3.6 Water level check

3. Reattach the water circuit (heat exhaust) compartment panel.

If water level in the humidifying tray water level regulator is low or

high, regulate it as follows.

1. Loosen the position adjusting screw and raise/lower the

humidifying tray water level regulator.

2. If water level cannot be regulated in step 1, loosen the nut and

turn the water level sensor clockwise (seen from above) to lower

water level, or counter-clockwise to raise it. Then, retighten the

nut.

3. Reattach the water circuit (heat exhaust) compartment panel and

set the main power switch in the ON position.

4. Press the POWER

key.

5. Run the cabinet at 30

and 40%RH.

6. Check water is the proper level.

If water level is okay, the cabinet is ready for use. If not, set the

main power switch in the OFF position and repeat steps 1 ~ 6.

Note

Procedure

Reference

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание LH-113















































































































Результаты поиска

Содержание LH-113

Отзывы:

Похожие инструкции для LH-113

Бренды по названию

Популярные бренды

ESPEC LH-113, Руководство пользователя

Результаты поиска

Содержание LH-113

Отзывы:

Похожие инструкции для LH-113

Бренды по названию

Популярные бренды