ESPEC LH-113 Скачать руководство пользователя страница 29

Страница: 29 / 110

Chapter 3 Installation

3.5 Water Level Check

(Not necessary with LU cabinet)

Water is supplied from the water tank to the humidifying tray. For proper

cabinet operation, water level in the tray must be checked.

•

Use distilled water of a 0.1 to 10 µS/cm conductivity. Using water

with a high impurity content, such as tap water, will shorten

service-life of the humidifying heater and wet-bulb wick.

•

Do not tilt the tank when full. Water will spill out.

To Fill the Water Tank

The water tank is filled by hand. This water is subsequently supplied to

the humidifying tray.

Press the POWER key and run the cabinet at 30ºC and 40%RH. For

details, see “Chapter 4 Operation”.

1. Prepare a water source a minimum of 500 mm higher than the water

tank nipple on the cabinet rear.

2. Connect the included snap-on water supply/drain hose (

9mm ID) to

the water tank nipple. See “3.3 Drainage Work”.

Water supply/drain hose

Water tank nipple

Water tank

Min. 500 mm

Fig. 3.5 Setup for adding water

3. Start water supply.

When the water tank becomes full (approx. 20L), the FULL lamp

(green) will light up. Stop water supply at that point.

Also, if wanting to leave the cabinet running unmanned for 2 to 3 days,

fill the water tank with distilled water in advance.

Note

Procedure

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание LH-113















































































































Результаты поиска

Содержание LH-113

Отзывы:

Похожие инструкции для LH-113

Бренды по названию

Популярные бренды

ESPEC LH-113, Руководство пользователя

Результаты поиска

Содержание LH-113

Отзывы:

Похожие инструкции для LH-113

Бренды по названию

Популярные бренды