Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 95

Страница: 95 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Diagnostics and troubleshooting

Hauser

Diagnostics and troubleshooting

13.1 General trouble shooting

13.1.1 General errors

Error

Possible cause

Remedial action

Device does not respond.

Supply voltage not connected.

Connect the correct voltage.

The cables do not contact the
terminals properly.

Ensure electrical contact between the
cable and the terminal.

Values on the display
invisible

Contrast setting is too weak or too
strong.

• Increase contrast by pressing  and

 simultaneously.

• Decrease contrast by pressing  and

 simultaneously.

The plug of the display cable is not
connected correctly.

Connect the plut correctly.

Display is defective.

Replace display.

"Communication error" is
indicated on the display when
starting the device or
connecting the display

Electromagnetic interference

Check grounding of the device.

Broken display cable or display plug.

Exchange display.

CDI communication does not
work.

Wrong setting of the COM port on
the computer.

Check the setting of the COM port on
the computer and change it if necessary.

Device measures incorrectly.

Parametrization error

Check and adjust parameterization.

13.1.2 Parametrization errors

Error

Possible cause

Remedy

Measured value incorrect

If measured distance (Setup
→ Distance) matches the real
distance:
Calibration error

• Check and adjust

Empty calibration

parameter (→  128) if necessary.

• heck and adjust

Full calibration

parameter (→  129) if necessary.

• Check and adjust linearization if

necessary (

Linearization

submenu

(→  144)).

Wrong level correction

Enter correct value in

Level correction

parameter (→  141).

If measured distance (Setup
→ Distance) does not match the real
distance:
Interference echo

Carry out tank mapping (

Confirm

distance

parameter (→  131)).

No change of measured value
on filling / emptying

Interference echo from installations,
nozzle or build-up on the antenna.

• Carry out tank mapping (

Confirm

distance

parameter (→  131)).

• If possible, align antenna in the

direction of the solid surface in order
to prevent interference echoes.

• If necessary, clean antenna (purge

air).

• If necessary, select a better mounting

position and/or larger antenna.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды