Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 156

Страница: 156 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

156

Hauser

"Switch output" submenu

Navigation

 Setup → Advanced setup → Switch output

Switch output function



Navigation

 Setup → Advanced setup → Switch output → Switch out funct

Description

Select function for switch output.

Selection

• Off

• On

• Diagnostic behavior

• Limit

• Digital Output

Factory setting

Off

Additional information

Meaning of the options

•

Off

The output is always open (non-conductive).

•

The output is always closed (conductive).

•

Diagnostic behavior

The output is normally closed and is only opened if a diagnostic event is present. The

Assign diagnostic behavior

parameter (→  157) determines for which type of event

the output is opened.

•

Limit

The output is normally closed and is only opened if a measured variable exceeds or falls

below a defined limit. The limit values are defined by the following parameters:

–

Assign limit (→  157)

–

Switch-on value (→  158)

–

Switch-off value (→  159)

•

Digital Output

The switching state of the output tracks the output value of a DI function block. The

function block is selected in the

Assign status

parameter (→  156).

The

Off

and

options can be used to simulate the switch output.

Assign status



Navigation

 Setup → Advanced setup → Switch output → Assign status

Prerequisite

Switch output function (→  156)

Digital Output

Description

Select device status for switch output.

Selection

• Off

• Digital output AD 1

• Digital output AD 2

• Digital output 1

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды