Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 46

Страница: 46 / 198

Operation options

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Hauser

8.2

Structure and function of the operating menu

8.2.1

Structure of the operating menu

Submenu /
parameter

Meaning

Language

Defines the operating language of the
on-site display.

Setup

Parameter 1
...
Parameter N

When all these parameters have been
assigned appropriate values, the
measured should be completely
configured in a standard application.

Advanced setup

Contains further submenus and
parameters:
• to adapt the device to special

measuring conditions.

• to process the measured value

(scaling, linearization).

• to configure the signal output.

Diagnostics

Diagnostic list

Contains up to 5 currently active error
messages.

Event logbook

Contains the last 20 messages (which
are no longer active).

Device information

Contains information needed to identify
the device.

Measured values

Contains all current measured values.

Data logging

Contains the history of the individual
measuring values.

Simulation

Used to simulate measured values or
output values.

Device check

Contains all parameters needed to check
the measurement capability of the
device.

Heartbeat

Contains all wizards for the

Heartbeat

Verification

and

Heartbeat Monitoring

application packages.

Expert

Contains all parameters of the device
(including those which are already contained
in one of the above submenus). This menu is
organized according to the function blocks of
the device.
The parameter of the

Expert

menu are

described in:
GP01017F (FOUNDATION Fieldbus)

System

Contains all general device parameters
which do not affect the measurement or
the communication interface.

Sensor

Contains all parameters needed to
configure the measurement.

Output

Contains all parameters neeed to
configure the switch output (PFS).

Communication

Contains all parameters needed to
configure the digital communication
interface.

Diagnostics

Contains all parameters needed to
detect and analyze operational errors.

In case of operation via operating tools (e.g. FieldCare), the "Language" parameter is located at "Setup →
Advanced setup → Display"

only available with local operation

only available for operation via DeviceCare or FieldCare

On entering the "Expert" menu, an access code is always requested. If a customer specific access code has
not been defined, "0000" has to be entered.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды