Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 168

Страница: 168 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

168

Hauser

"Configuration backup display" submenu

This submenu is only visible if a display module is connected to the device.

The configuration of the device can be saved to the display module at a certain point of

time (backup). The saved configurateion can be restored to the device if required, e.g. in

order to bring the device back into a defined state. The configuration can also be

transferred to a different device of the same type using the display module.

Navigation

 Setup → Advanced setup → Conf.backup disp

Operating time

Navigation

 Setup → Advanced setup → Conf.backup disp → Operating time

Description

Indicates how long the device has been in operation.

User interface

Days (d), hours (h), minutes (m), seconds (s)

Additional information

Maximum time

999 d ( ≈ 27 years)

Last backup

Navigation

 Setup → Advanced setup → Conf.backup disp → Last backup

Description

Indicates when the last data backup was saved to the display module.

User interface

Days (d), hours (h), minutes (m), seconds (s)

Configuration management



Navigation

 Setup → Advanced setup → Conf.backup disp → Config. managem.

Description

Select action for managing the device data in the display module.

Selection

• Cancel

• Execute backup

• Restore

• Duplicate

• Compare

• Clear backup data

• Display incompatible

Factory setting

Cancel

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды