Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 59

Страница: 59 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Operation options

Hauser

8.3.4

Opening the context menu

Using the context menu, the user can call up the following menus quickly and directly from

the operational display:
• Setup

• Conf. backup disp.

• Simulation

Calling up and closing the context menu

The user is in the operational display.

1. Press  for 2 s.

 The context menu opens.

XXXXXXXXXX

kg/h

20.50

Setup

Conf.backup disp

Simulation

A0014003-EN

2. Press  +  simultaneously.

 The context menu is closed and the operational display appears.

Calling up the menu via the context menu

1. Open the context menu.
2. Press  to navigate to the desired menu.
3. Press  to confirm the selection.

 The selected menu opens.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды