Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 167

Страница: 167 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Operating menu

Hauser

167

Selection

• x

• x.x

• x.xx

• x.xxx

• x.xxxx

Factory setting

x.xxxx

Additional information

• Is only valid for numbers in the operating menu (e.g.

Empty calibration

Full

calibration

), but not for the measured value display. The number of decimal places for

the measured value display is defined in the

Decimal places 1 to 4

→  164

parameters.

• The setting does not affect the accuracy of the measurement or the calculations.

Backlight

Navigation

 Setup → Advanced setup → Display → Backlight

Prerequisite

The device has the SD03 local display (with optical keys).

Description

Switch the local display backlight on and off.

Selection

• Disable

• Enable

Factory setting

Disable

Additional information

Meaning of the options

•

Disable

Switches the backlight off.

•

Enable

Switches the backlight on.

Regardless of the setting in this parameter the backlight may be automatically

switched off by the device if the supply voltage is too low.

Contrast display

Navigation

 Setup → Advanced setup → Display → Contrast display

Description

Adjust local display contrast setting to ambient conditions (e.g. lighting or reading angle).

User entry

20 to 80 %

Factory setting

Dependent on the display.

Additional information

Setting the contrast via push-buttons:

• Darker: press the and

buttons simultaneously.

• Brighter: press the and

buttons simultaneously.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды