Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 29

Страница: 29 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Installation

Hauser

Nozzle mounting

The horn antenna should protrude from the nozzle. If this is not possible for mechanical

reasons, larger nozzle heights can be accepted.

A0016825

 8

Nozzle height for the horn antenna (FMR57)

Antenna

Maximum nozzle height

max

BC: Horn 80mm/3"

260 mm (10.2 in)

BD: Horn 100mm/4"

480 mm (18.9 in)

Feature 070 of the product structure

valid for antennas without antenna extension

Please contact Hauser for applications with higher nozzle.

Threaded connection

For devices with a threaded connection it may be necessary - depending on the

antenna size - to unmount the horn before fastening the device and to mount it again

afterwards.

• Tighten with the hexagonal nut only.

• Tool : 60 mm hexagonal wrench

• Maximum permissible torque: 60 Nm (44 lbf ft)

6.3.4

Parabolic antenna (FMR57)

Alignment

Ideally, the parabolic antenna should be installed vertically. To avoid interference

reflections or for optimum alignment within the vessel, the Micropilot with optional

alignment device can be swiveled by 15° in all directions →  32.

Nozzle mounting

• Case 1: Ideally, the parabolic antenna should protrude from the nozzle (1). Particularly

when using the alignment device, please ensure that the parabolic reflector is protruding

from the nozzle/roof so as not to inhibit alignment.

• Case 2: For applications with higher nozzle it may be necessary to install the parabolic

antenna completely in the nozzle (2).

The maximum height of the nozzle (H

max

) to the parabolic mirror should not exceed

500 mm (19.7 in). Interfering edges within the nozzle should be avoided.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды