Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 164

Страница: 164 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

164

Hauser

Value 1 to 4 display



Navigation

 Setup → Advanced setup → Display → Value 1 display

Description

Select the measured value that is shown on the local display.

Selection

• None

• Level linearized

• Distance

• Current output 1

• Measured current

• Current output 2

• Terminal voltage

• Electronic temperature

• Absolute echo amplitude

• Relative echo amplitude

• Analog output adv. diagnostics 1

• Analog output adv. diagnostics 2

• Area of incoupling

Factory setting

• Value 1 display: Level linearized

• Value 2 display: None

• Value 3 display: None

• Value 4 display: None

Decimal places 1 to 4



Navigation

 Setup → Advanced setup → Display → Decimal places 1

Description

Select the number of decimal places for the display value.

Selection

• x

• x.x

• x.xx

• x.xxx

• x.xxxx

Factory setting

x.xx

Additional information

The setting does not affect the measuring or computational accuracy of the device.

Display interval

Navigation

 Setup → Advanced setup → Display → Display interval

Description

Set time measured values are shown on display if display alternates between values.

can not be selected for the 'Value 1 display" parameter.

Visibility depends on order options or device settings

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды