Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 178

Страница: 178 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

178

Hauser

17.4.3 "Device information" submenu

Navigation

 Diagnostics → Device info

Device tag

Navigation

 Diagnostics → Device info → Device tag

Description

Enter tag for measuring point.

Factory setting

FMP5x

Serial number



Navigation

 Diagnostics → Device info → Serial number

Description

Displays serial number of the device.

Additional information

Uses of the serial number

• To identify the device quickly, e.g. when contacting Hauser.

• To obtain specific information on the device using the Device Viewer:

www.endress.com/deviceviewer

The serial number is also indicated on the nameplate.

Firmware version

Navigation

 Diagnostics → Device info → Firmware version

Description

Indicates the installed Firmware version.

User interface

xx.yy.zz

Additional information

For firmware versions differing only in the last two digits ("zz") there is no difference

concerning functionality or operation.

Device name

Navigation

 Diagnostics → Device info → Device name

Description

Displays device name.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды