Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 112

Страница: 112 / 198

Accessories

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

112

Hauser

16.1.5 Horn protection for horn antenna

Accessory

Description

Horn protection for
80 mm (3 in) or
100 mm (4 in) horn
antenna

øD

ød

A0019143

Horn antenna of the Micropilot (not supplied with the horn protection)

Horn protection

⌀d Diameter of horn protection (see table below)
⌀D Minimum nozzle diameter (see table below)
L

Length of antenna with horn protection (see table below)

For details please refer to the Mounting Instructions SD01084F.

Process conditions

• Maximum vessel pressure: 0.5 bar (7.252 psi)
• Maximum process temperature: 130 °C (266 °F)



Danger of explosion
Avoid electrostatic charging of the horn protection.

Horn protection for FMR57

Antenna

Order code horn
protection

Dimensions a horn protection

Ød

ØD

BC: Horn 80mm/3"

71105890

238 mm (9.4 in)

96 mm (3.78 in)

≥ DN100

BD: Horn 100mm/4"

71105889

450 mm (17.7 in)

116 mm (4.57 in)

≥ DN150

Feature 070 of the product structure

The horn protection can also be ordered together with the device. Product structure:

Feature 610 "Accessory Mounted", option OW "Horn protection, PTFE".

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды