Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 177

Страница: 177 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Operating menu

Hauser

177

17.4.2 "Event logbook" submenu

The

Event logbook

submenu is only available when operating via the local display.

When operating via FieldCare, the event list can be displayed in the FieldCare

function "Event List / HistoROM".

Navigation



Diagnostics → Event logbook

Filter options



Navigation



Diagnostics → Event logbook → Filter options

Description

Select category (status signal) whose event messages are displayed in the events list.

Selection

• All

• Failure (F)

• Function check (C)

• Out of specification (S)

• Maintenance required (M)

• Information (I)

Factory setting

All

Additional information

• This parameter is only used for operation via the local display.

• The status signals are categorized according to NAMUR NE 107.

"Event list" submenu

The

Event list

submenu displays the history of past events of the category selected in the

Filter options

parameter (→  177). A maximum of 100 events are displayed in

chronological order.
The following symbols indicate whether an event has occurred or has ended:

•

: Event has occurred

•

: Event has ended

Information on what is causing the message, and remedy instructions, can be viewed

via the -button.

Display format

• For event messages in category I: information event, event text, "recording event" symbol

and time the event occurred

• For event messages in category F, M, C, S (status signal): diagnostics event, event text,

"recording event" symbol and time the event occurred

Navigation



Diagnostics → Event logbook → Event list

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды