Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 152

Страница: 152 / 198

Operating menu

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

152

Hauser

Factory setting

0 %

Level (Semiautomatic)

Navigation



Setup → Advanced setup → Linearization → Level

Prerequisite

•

Linearization type (→  146)

Table

•

Table mode (→  150)

Semiautomatic

Description

Displays measured level (value before linearization). This value is transmitted to the table.

Customer value



Navigation



Setup → Advanced setup → Linearization → Customer value

Prerequisite

Linearization type (→  146)

Table

Description

Enter linearized value for the table point.

User entry

Signed floating-point number

Factory setting

0 %

Activate table



Navigation

 Setup → Advanced setup → Linearization → Activate table

Prerequisite

Linearization type (→  146)

Table

Description

Activate (enable) or deactivate (disable) the linearization table.

Selection

• Disable

• Enable

Factory setting

Disable

Additional information

Meaning of the options

•

Disable

The measured level is not linearized.

Linearization type (→  146)

Table

at the same time, the device issues error

message F435.

•

Enable

The measured level is linearized according to the table.

When editing the table, the

Activate table

parameter is automatically reset to

Disable

and must be reset to

Enable

after the table has been entered.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды