Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 23

Страница: 23 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Installation

Hauser

A0017125

6.1.5

Optimization options

• Antenna size

The bigger the antenna, the smaller the beam angle α and the fewer interference echoes

→  24.

• Mapping

The measurement can be optimized by means of electronic suppression of interference

echoes.

See the

Confirm distance

parameter (→  131) for details.

• Antenna alignment

Take into account the marker on the flange or threaded connection →  26.

• Metallic screens mounted at a slope

They spread the radar signals and can, therefore, reduce interference echoes.

• Variable flange seal (FMR56)

Using the variable flange seal, the device can be aligned in the direction of the product

surface. For details refer to Operating Instructions BA01048F, chapter "Accessories".

• Alignment device for FMR57

In FMR57 with alignment device, the sensor can be optimally aimed within the vessel

and thus interference echoes can be avoided. The maximum angle β is ±15°.

In particular, sensor alignment serves to:

– prevent interference reflections

– extend the maximum possible measuring range in conical outlets

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды