Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 159

Страница: 159 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Operating menu

Hauser

159

A0015586

Switch-on value

Switch-off value

Output closed (conductive)

Output opened (non-conductive)

Switch-on delay



Navigation

 Setup → Advanced setup → Switch output → Switch-on delay

Prerequisite

•

Switch output function (→  156)

Limit

•

Assign limit (→  157)

≠

Off

Description

Define switch-on delay.

User entry

0.0 to 100.0 s

Factory setting

0.0 s

Switch-off value



Navigation

 Setup → Advanced setup → Switch output → Switch-off value

Prerequisite

Switch output function (→  156)

Limit

Description

Enter measured value for the switch-off point.

User entry

Signed floating-point number

Factory setting

Additional information

The switching behavior depends on the relative position of the

Switch-on value

and

Switch-off value

parameters; description: see the

Switch-on value

parameter

(→  158).

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды