Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 189

Страница: 189 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Operating menu

Hauser

189

Description of parameters

Navigation

 Expert → Diagnostics → Simulation

Assign measurement variable



Navigation

 Expert → Diagnostics → Simulation → Assign meas.var.

Description

Selct process variable to be simulated.

Selection

• Off

• Level

• Level linearized

Factory setting

Off

Additional information

• The value of the variable to be simulated is defined in the

Value process variable

parameter (→  189).

• If

Assign measurement variable

≠

Off

, a simulation is active. This is indicated by a

diagnotic message of the

Function check (C)

category.

Value process variable



Navigation

 Expert → Diagnostics → Simulation → Value proc. var.

Prerequisite

Assign measurement variable (→  189)

≠

Off

Description

Specify value of the process value being simulated.

User entry

Signed floating-point number

Factory setting

Additional information

Downstream measured value processing and the signal output use this simulation value. In

this way, users can verify whether the measuring device has been configured correctly.

Switch output simulation



Navigation

 Expert → Diagnostics → Simulation → Switch sim.

Description

Switch the simulation of the switch output on or off.

Selection

• Off

• On

Factory setting

Off

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды