Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 87

Страница: 87 / 198

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Commissioning (block-based operation)

Hauser

12.8 Configuration of the event behavior according to the

FOUNDATION Fieldbus specification FF912

The device complies with the FOUNDATION Fieldbus specification FF912. This has -

among other things - the following consequences:
• The diagnsotic category according to NAMUR recommendation NE107 is transmitted via

the fieldbus in a manufacturer-independent form:

– F: Failure

– C: Function check

– S: Out of specification

– M: Maintenance required

• The diagnostic category of pre-defined groups of events can be adjusted by the user

according to the requirements of the specific application.

• Certain events can be separated from their group and can be handled individually:

– 941: Echo lost

– 942: In safety distance

– 950: Advanced Diagnostic occurred

• Additional information and remedial measures are transmitted together with the event

message via the fieldbus.

The diagnostic messages according to FF912 are available in the host only if the

Multi-bit support

option has been activated in the

FEATURE_SEL

parameter of the

Resource block. For reasons of compatibility, this option is

not

activated on delivery:

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды