Elkron MP500/16 страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 140

background image

8

MP500/4N-8-16 Programming

INTRODUCTION

ORGANISATION OF THE MANUAL

The manual is divided into chapters and the various topics are arranged in sequence to provide step-by-step instructions for

programming

and

configuring

the system.

Information for system

design, installation

and

maintenance

are contained in the

Installation Manual.

The Installation Manual also contains the

device acquisition procedure.

Instructions for system use by the end user are contained in the

User Manual.

CONVENTIONS USED

The following conventions are used in the manual for the sake of simplicity:

This is the LCD with the displayed message.
Unless otherwise specified, the same message is shown on the touchscreen keypad.

,

,

,

,

…

This is the equivalent key to be pressed on the keypad.

<Master code>
<User code>
<Installer code>
<Technical Manager code>

This indicates the code to be entered using the keypad.

<Master / User code>

This means that either code may be entered on the keypad indifferently.

H24

This means that the described function or service is always active.

Pay attention to the following symbols:

This symbol indicates an important warning.

This symbol indicates advice.

This symbol indicates EN50131 grade 3 compliance.
The compliance of the system as a whole is equal to the minimum certification of the installed devices and of the
enabled functions.

This symbol indicates EN50131 grade 2 compliance.
The compliance of the system as a whole is equal to the minimum certification of the installed devices and of the
enabled functions.

This symbol indicates that EN50131 compliance may depend on other functions enabled in the system.

The symbol means that the function or device is not EN50131 certified.

This symbol means that the function or device will cancel EN50131 certification.

«
...
6
7
8
9
10
...
»

Содержание MP500/16













































































































































Отзывы:

Нет отзывов

Похожие инструкции для MP500/16

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Lawler Страницы: 2

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Бренд: Magnescale Страницы: 132

Бренд: Unitech Страницы: 11

Бренд: B meters Страницы: 10

Бренд: Wavelink Страницы: 69

Бренд: Bartlett Страницы: 5

Бренд: Datavideo Страницы: 8

Бренд: GCE Страницы: 24

Бренд: Rabbit Страницы: 38

MusicCAST MCX-CA15

Бренд: Yamaha Страницы: 176

Бренд: Ziton Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды