manualshive.com logo in svg

Elkron MP500/16, Руководство по программированию, Страница: 120 / 140

Поделиться
Скачать
Elkron MP500/16 Скачать руководство пользователя страница 120

120 

  MP500/4N-8-16 Programming                                                               

 

 

 

9.5 

FIRMWARE UPGRADE AT POWER ON 

The firmware of the control panel and of all bus devices of the system can be upgraded automatically when the control panel is turned on. 
The necessary conditions, upgrade files and preliminary operations are the same as the firmware upgrading procedure from menu. 
 

9.5.1 

Device FW upgrade procedure at power on 

The procedure is shown below: 
1)  Remove all power from the control panel (remove main power and disconnect the back-up battery). 
2) 

Insert a jumper between the pins 5 and 6 of the “SERVICE” connector on the motherboard of the control panel. 

3)  Plug the IT USB/KEY interface into the J11 connector of the control panel. 
4)  Insert  the  USB  memory  stick,  onto  which  the  upgrade  files  were  previously  copied  (.bin),  into  the  USB  port  of  the  IT  USB/KEY 

interface. 

5)  Power the control panel again (mains power and back-up battery). 
 

Note

:  Implement  the  appropriate  actions  to  block  the  fail-safe  siren  commands  or  otherwise  disconnect  the  power  by  removing  the 

internal back-up batteries. 
 
When power is restored, the control panel will check: 

 

presence of the jumper JP on the “SERVICE” connector  

 

presence of the interface  

 

presence of the USB memory stick. 

Upgrading may not be successful if only one of these conditions is not respected. 
 
If the check was successful: 

 

The control panel will automatically start the upgrade procedure towards the system devices (the devices which can be upgrade d 
are set to "BOOT" status). 

 

The control panel will upgrade the devices of the same type in parallel (keypads, expansion modules etc.) checking the result and 
repeating the procedure automatically in case of errors. 

 

During the entire upgrade procedure, the run LED lights up o

n the control panel according to the “Running” sequence (blinking for 

1.6 seconds - off for 0.5 seconds). 

 
After upgrading, one of the following indications will appear according to the result type. 
 

 

Positive result.

 The procedure was successful. 

The run L

ED will light up on the control panel according to the “Successful Update” sequence (off for 2 seconds - blinking for 2 

seconds). 

 
 

 

IMPORTANT! 

This  indication  will  appear  even  if  the  procedure  never  started.  No  device  can  be  upgraded  or  the 

devices have 

the same upgrade file release (“filename”.BIN). 

 

 

Negative result

. The procedure was interrupted or is not OK. 

The run LED will light up on the control panel according to the “Update was not successful” sequence (on for 2 seconds - blinking 
for 2 seconds). 

 
 

 

IMPORTANT! 

This indication will also appear if one of the following errors occurs: 

 

o

 

The USB memory stick does not respond. 

o

 

The files (.bin) are not in the dedicated folder (UPG). 

o

 

Despite the automatic upgrade attempts all or some devices have not completed the procedure: communication interrupted, 
incorrect download (CRC KO), flash writing KO. 

o

 

The devices which do not complete programming successfully will remain in "BOOT" state and will not be used in the system 
until they are reprogrammed. 

 
The control panel will maintain one of the two indication sequences until the control panel power off. 
 
To make the upgrade definitive and return the system to operating conditions: 
1.  Remove all power from the control panel (remove main power and disconnect the back-up battery). 
2. 

Remove the jumper between the pins 5 and 6 of the “SERVICE” connector on the motherboard of the control panel. 

3.  Unplug the IT USB/KEY interface from the J11 connector of the control panel. 
4.  Power the control panel again (mains power and back-up battery). 
 

Содержание MP500/16













































































































































Отзывы:

Нет отзывов