manualshive.com logo in svg

Dräger Cicero EM, Инструкция по эксплуатации

Поделиться
Скачать
Dräger Cicero EM Скачать руководство пользователя страница 111

Message, cause and remedy 

Messages in the ventilation system

Message must be acknowledged

Messages during
the self-test

Cause

Remedy

Breathing sys. defect. • Valve V

6

 not closing.

Replace breathing system or valve plate.

Display 

»109«

 

in V

T

 field

Breathing sys. defect. • Additional air valve not opening.

Replace breathing system or valve.

Display 

»111«

 

in V

T

 field

Breathing sys. defect.  • APL (overpressure) valve faulty.

Replace breathing system or valve.

Display 

»121«

 

in V

T

 field 

Breathing system leak • Major leak in breathing system (absorber 

Repair leak. Confirm.

missing, no valve plates, breathing system 
not fully locked)

Compl. test please

If the self-test is interrupted:
If a malfunction message was previously 

Switch off audible alarm by

stored, this message switches the device 

acknowledging message. Restart.

to 

»Man/Spont.«

 mode

(mechanical ventilation is only possible 
after fault-free completion of the self-test)

Control pressure low

• Insufficient operating control pressure. 

Breathing system or roller diaphragm faulty.

Breathing system and piston pump 

Replace defective parts.

installed and locked?
Supply pressure greater than 2.7 bar ?

Fresh gas off ?

• Dialogue during the self-test.

Shut off the gas metering.

Insp. valve ?

• Indication of possible fault:

Is the valve disc in the inspiration valve 

Check valve. Change faulty parts. 

faulty? Crater damaged? 

Remedy leak.

Leak in subsystem 1? 
See flow chart on page 164.

Install piston

• Piston pump not installed.

Install piston pump.

Leak = xxx mL/min

• Indicates a leak in the ventilation system. 

Acknowledge. 

For leaks greater than 300 mL/min 

Repair any leak and repeat the test.

(at 30 mbar) in subsystem 3. 
See flow chart on page 164.

Leak accepted?

• Indicates a leak in the ventilation system.

The user accepts by confirming the previously
displayed leak. The test continues.

Leak IPPV = xxx mL

Displayed at the end of the leak test in 

For information.

subsystem 1/2 for approx. 2 seconds if 
the leak < 175 mL/min.
See flow chart on page 164.

111

Содержание Cicero EM





































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды