Dräger Cicero EM Скачать руководство пользователя страница 104

Страница: 104 / 196

104

Message, cause and remedy

Messages on the system screen

(In alphabetical order according to priority)

Messages

Cause

Remedy

Caution messages

AMV

Minute volume below lower alarm limit.

Tube blocked / kinked?

Leak in breathing system?

Pressure limited ventilation?

Check tube and hoses.

Seal breathing system.

Adjust ventilation pattern.

AMV

Minute volume exceeds upper alarm limit.

Correct tidal volume or
respiration rate on ventilator.

DIA NIBP

Measured non-invasive blood pressure below
lower alarm limit.

Check patient's condition!

Correct alarm limit if necessary.

DIA NIBP

Measured non-invasive blood pressure exceeds
upper alarm limit.

Check patient's condition!

Correct alarm limit if necessary.

DIAS IBP1

DIAS IBP2

Measured invasive diastolic pressure of the
channel shown (1 or 2) below lower alarm limit.

Check patient's condition!

Correct alarm limit if necessary.

DIAS IBP1

DIAS IBP2

Measured invasive diastolic pressure of the
channel shown (1 or 2) exceeds upper alarm limit.

Check patient's condition!

Correct alarm limit if necessary.

ET CO2

Upper alarm limit for end-expiratory CO

concentration has been exceeded for at least two
breaths.

Check ventilation

ET CO2

End-expiratory CO

concentration below lower

alarm limit for at least two breaths.

Check ventilation.
Check for leak in sample line.

EXSP-V INOP !!

Fault in expiration valve. Measured value for minute
ventilation may be excessive.

Check expiration valve.
Carry out another leak test.

Fl O2

Inspiratory O

concentration exceeds upper alarm

limit.

Check O

concentration in fresh

gas flow.

This message is deactivated
until the next leakage test by
pressing the alarm suppressor
key.

Fl HAL

Fl ISO

Fl ENF

Fl DES

Fl SEV

Applicable inspiratory anaesthetic concentration
below lower alarm limit.

Value below lower alarm limit for at least two
breaths.

Check setting of anaesthetic
vaporizer.

FRESH GAS ? !!

Too little gas in manual ventilation bag.

Increase fresh gas flow. Repair
any leaks in hose system.

HEART RATE

Heart rate exceeds set upper limit.

Check patient's condition!

Correct alarm limit if necessary.

INSP CO2

The inspiratory CO

concentration exceeds the

upper alarm limit.

Check the soda lime.

Check the valve plate in the
breathing system.

Correct alarm limit if necessary.

Содержание Cicero EM





































































































































































































Результаты поиска

Содержание Cicero EM

Отзывы:

Бренды по названию

Популярные бренды

Dräger Cicero EM, Инструкция по эксплуатации

Результаты поиска

Содержание Cicero EM

Отзывы:

Бренды по названию

Популярные бренды