Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 69 / 192

desCrIpTION OF OperATING sysTeM

ENGINE COOlANT TEMPERATuRE GAuGE

This gauge indicates the coolant

temperature after the key switch is

turned to the "ON" position.

•

: Coolant is cold.

•

: Coolant is hot.

The range marked in "2" in the figure

indicates the normal engine tempera-

ture. (Normal driving range)

(1) Coolant Temperature Gauge

(2) Normal driving range

C : Cold

h : hot

M46O413A

This lamp comes on when the en-

gine oil pressure or oil level is low.
This lamp is turned "ON" when the

starting switch is turned "ON" before

starting the engine but turned "OFF"

after starting the engine. If this lamp

comes with buzzer on while driving,

stop the engine immediately and

check the engine oil level.
If this lamp comes on even with the

specified engine oil level, have the

tractor checked by your local

KIOTI

dealer or workshop immediately.

ENGINE OIl PRESSuRE wARN-

ING lAMP

M46O417A

Make sure to control the work

load so that the needle is not

in the red zone.
If the needle stays in the red

zone with buzzer, do not stop

the engine immediately. In-

stead, reduce the work load to

cool down the engine before

stopping the engine.
Make sure to keep the front

grill clean so that air is sucked

through it freely for fast cooling.

•

CAuTION

M46-EU,AU-EEC인증용-04.indd 11

2017-06-16 오후 1:06:54

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды