Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 101 / 192

opERATIoN

M46O505A

M46O431A

Always.wear.the.seat.belt.

If.the.seat.belt.is.worn.across.

the.abdomen.or.waist,.not.the.

hips,.an.injury.can.occur.in.

case.of.an.accident.or.impact.

Do.not.wear.the.seat.belt.if.

the.ROPS.is.not.installed.or.

folded.

•

WARNING

(1) Hand Throttle lever

: Decrease

: Increase

H11O511A

(1) Seat Belt

2. Wear the seat belt.

3. pull the position control lever back-

ward to raise the attachment.

(1) position Control lever

(A) lifting

4. Increase slowly the engine Rpm

from idle speed to medium speed.

M46-EU,AU-EEC인증용-05.indd 11

2017-03-10 오전 8:27:34

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды