Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 50 / 192

Cs2610

General specifications

external diMensions

※

these dimensions are measured with the standard tires installed to the

rops

model tractor.

M46O301B

iteM

cs2610

1. overall length (a1)

2,800 (110.23)

2. overall length (a2)

2,523 (99.33)

3. overall width (b)

1,270 (50.00)

4. overall height (C1)

1,899 (74.76)

5. overall height (C2)

2,280 (89.76)

6. Wheel base (d)

1,400 (55.12)

7. tread (E1)

930 (36.61)

8. tread (E2)

870 (34.25)

9. min. ground clearance (F)

162 (6.38)

mm (in.)

※

a1: overall length including weights and folded

rops

a2: overall length excluding weights

C1: overall height with folded

rops

C2: overall height with raised

rops

E1: Front wheel tread

E2: rear wheel tread

M46-EU,AU-EEC인증용-03.indd 2

2017-04-27 오전 9:07:53

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды