Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 180 / 192

CS2610

causE

counTErMEasurEs

When engine is difficult to

start

•

Fuel is thick and doesn’t flow.

•

Check the fuel tank and fuel filter.

•

Remove water, dirt and other impurities.

•

All fuel will be filtered by the filter, if there should be water of

other foreign material on the filter, replace the filter.

•

Air or water mixed in fuel system.

•

If air is in the fuel filter or injection lines, the fuel pump will

not work properly.

•

To attain proper fuel injection pressure, check carefully for

loosened fuel cap nut, etc.

•

Loosen air vent screw over fuel filter and fuel injection pump

to eliminate all the air in the fuel system.

•

Thick carbon deposits on orifice

of injection nozzle.

•

This is caused when water or dirt is mixed in the fuel. Clean

the nozzle injection piece, being careful not to damage the

orifice.

•

Check to see if nozzle is working properly or not, if not,

install a new nozzle.

•

Valve clearance is wrong

•

Contact

KioTi

dealer.

•

Engine oil become thick in cold

weather and engine cranks slow.

•

Change grade of oil according to the weather. (temperature)

This troubleshooting chart summarizes simple service items for users who are familiar with mechanical systems.
For more detailed service items, contact your local

KioTi

Dealer.

EnginE TroublEshooTing

M46-EU,AU-EEC인증용-09.indd 2

2017-03-10 오전 8:51:15

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды