Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 77 / 192

desCrIpTION OF OperATING sysTeM

FORwARD / REvERSE DRIvING PEDAlS

(1) Forward / reverse driving pedals

(A) Forward

(b) reverse

Left pedal is for forward driving and

right pedal is for reverse driving.

M46O432A

HAND THROTTlE lEvER

M46O431A

(1) hand Throttle Lever

: decrease : Increase

The hand throttle lever is to control

the engine rpm. The engine acceler-

ates to its full speed by pulling the

hand throttle lever ( position)

completely out while pushing the

lever ( position) decelerates the

engine.
The hand throttle lever is mainly

used while working in a field.

"unlike a gas pedal, these for-

ward / reverse driving pedals-

act like a main speed shift in a

mechanical tractor." Therefore,

depress them deeper to obtain

higher speed with lower torque

and release them to obtain low-

er speed with higher torque.

•

IMPORTANT

For heavy load job, such as

front end loader operation,

use low speed of the range

shift lever.

•

IMPORTANT

M46-EU,AU-EEC인증용-04.indd 19

2017-06-16 오후 1:07:02

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды