Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 111 / 192

opERATIoN

If.stopping.the.engine.while.

driving,.the.steering.perfor-

mance.can.become.deterio-

rated.due.to.loss.of.hydraulic.

power,.resulting.in.a.severe.

accident..Never.stop.the.en-

gine.while.driving.

Do.not.release.the.steering.

wheel.to.return.to.the.straight-

ahead.position.after.turning.

while. driving.. The. steering.

wheel.in.this.tractor.is.not.a.

self-return.type..Releasing.the.

steering.wheel.while.driving.

may.lead.to.a.massive.acci-

dent.

•

WARNING

When.driving.on.a.road.with.an.

implement.attached.to.the.rear.

of.the.tractor,.the.traction.of.

the.front.wheels.becomes.poor,.

resulting.in.poor.steer.ability..In.

this.case,.attach.a.proper.front.

weight.and.drive.at.a.low.speed.

If.malfunction.occurs.while.driv-

ing.on.a.road,.stop.the.tractor.

in.a.safe.place.and.service.it..If.

it.is.not.possible.to.move.the.

tractor,.set.a.warning.triangle.

behind.the.tractor..Otherwise,.

an.rear.end.accident.may.occur.

The.center.of.gravity.of.the.trac-

tor.is.higher.compared.to.other.

common.vehicles,.so.the.pos-

sibility.of.a.roll-over.accident.

is.very.high..Be.extra.careful.

when.driving.on.a.lateral.slope,.

bumpy.road,.road.with.puddles,.

and.narrow.road..make.sure.to.

set.the.ROPS.in.its.original.po-

sition.and.fasten.the.seat.belt.

•

WARNING

The 3-point hitch can be controlled by

the position control lever. The lever in-

stalled on the center side (away from

the driver) is the position control lever.

3-POINT.HITCH.CONTROl.SySTEm

M46O438A

(1) position Control lever

(2) lower link

(A) lowering

(B) lifting

M46-EU,AU-EEC인증용-05.indd 21

2017-03-10 오전 8:27:40

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды