Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 93 / 192

opERATIoN

To.avoid.accidents:

Be.sure.to.read.and.under-

stand.the.warning.and.caution.

decals. on. the. tractor. thor-

oughly.

Run.the.engine.only.in.a.well-

ventilated.area,.or.you.can.be.

suffocated.by.exhaust.fumes.

Never.start.the.engine.unless.

you.are.on.the.driver’s.seat..

. The.tractor.can.abruptly.start.

off,.resulting.in.an.injury.or.

accident.

•

WARNING

Using. an. additive. so. the. en-

gine.will.start.more.easily.can.

damage.the.engine..And.it.will.

not.be.covered.by.warranty.
Never. try. to. start. the. engine.

for.over.10.seconds.consecu-

tively. to. protect. the. start. mo-

tor.and.battery.from.damage.

•

ImPORTANT

1. Break in the vehicle within initial 50

hours of operation.

2. Start the engine and idle the en-

gine at a low speed for 3 to 4 min-

utes in advance.

3. Increase the idling time in cold

weather.

4. Do not drive the tractor at the max-

imum speed on a road.

5. Never apply excessive load during

work.

6. Idle the engine at a low speed for

2 to 3 minutes before stopping it.

Driving a new tractor at a high speed

or load can damage its overall dura-

bility.
make sure to run the tractor at the

proper work load and speed for the

initial operation of 10 to 20 hours.

INITIAl.OPERATION

OPERATING.THE.ENGINE

STARTING.THE.ENGINE

SAfETy.lOCk.fUNCTION.(WHIlE.

vEHIClE.IS.STATIONARy)

1) The engine can be started only un-

der the following conditions due to

its safety lock function:

•

The range shift lever is in the

neutral position.

•

The pTo clutch is disengaged.

•

The driver's seat is occupied.

2) The tractor cannot be driven with

the forward and reverse driving

pedals depressed simultaneously

while the engine is running.

In order to drive the tractor, first re

lease the pedals. Then, the safety

lock will be deactivated in approx. 0.5

seconds and the tractor is ready to

drive.

TIPS.fOR.BREAkING-IN

M46-EU,AU-EEC인증용-05.indd 3

2017-03-10 오전 8:27:29

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды