Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 122 / 192

cs2610

M46O602A

(1) Lift Rod

(2) Turnbuckle

(3) Lock Nut

1. Adjust the implement level bal-

anced by turning the turnbuckle.

2. After adjustment, fix it with the lock

nut

ADjUsTMENT Of LIfT ROD

(1) Top Link

(2) Pin

(3) Retainer Pin

(4) Top Link hook

1. Install the top link to the desired

position, and install the pin and re-

tainer pin.

2. Fix Top link with fixed nut after ad

justing top link.

M46O603A

ADjUsTMENT Of TOP LINK

stop the engine and lower the

attachment to the ground prior

to disconnecting the lift rod

from the lower link. Check that

the attachment has proper

support and that there’s pres-

sure remaining in the hydrau-

lic system to remove the lift

rod holding the pin. To elimi-

nate the remaining pressure,

move the hydraulic adjusting

lever back and forth several

times.

•

WARNINg

When there is no implement at-

tached, fix the lower link to the

check link (Lh/Rh) so that it

does not contact with the rear

wheel.
secure the top link to the stor-

age hook.

•

NOTE

M46-EU,AU-EEC인증용-06.indd 6

2017-04-26 오전 11:41:52

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды