Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 129 / 192

3-POINT hITch IMPLEMENT OPERATION

DRIvINg ON sLOPE

WHEN LOADED BUCKET AND REAR BALLAsT ARE INsTALLED

H11O554A

DRIvINg ON UPHILL

When driving uphill with a loaded

bucket and rear ballast installed,

H11O555A

DRIvINg ON DOWNHILL

H11O556A

DRIvINg ON UPHILL

H11O557A

DRIvINg ON DOWNHILL

WHEN UNLOADED BUCKET AND

REAR BALLAsT ARE INsTALLED

To avoid injuries:

Keep the loader arm as low

as possible when driving on a

slope.

•

WARNINg

When driving on downhill with an

empty bucket and rear ballast in-

keep the higher end of the tractor

heavier. In other words, drive forward

on uphill and backward on downhill.

M46-EU,AU-EEC인증용-06.indd 13

2017-04-26 오전 11:41:59

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды