Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 34 / 192

cs2610

WARNING

Use of the front loader and of

the tractor equipped with front

loader, if not correctly carried

out, and handling not secured

loads constitute a serious dan-

ger for the operator and every-

one standing by, because of

the danger of falling objects.

•

Tg2O110a

• three-point hitch and side mounted

implements make a much larger

arc when turning than towed equip-

ment. make certain to maintain

enough clearance for safe turning.

• to use mounted, semi-mounted

or towed equipment and trailers it

is required to use exclusively ce

marked implements, after reading

their operation handbooks carefully,

giving maximum attention to risks

connected with their association to

the tractor.

• implements must be hitched to the

tractor by means of the three-point

linkage. it is therefore necessary

to check couplings for compatibility

according to their classes.

The implement has to be fitted with

suitable supports in order to avoid

tipping or accidental shifting dur-

ing hitching. always check three-

directional fastening to the tractor

of the mounted or semi-mounted

implement, to avoid dangerous

swinging and shaking during trans-

port and work that could jeopardize

the stability of the tractorimplement

assembly.

• the cardan shaft must be always

ce-marked, provided with suit-

able guards and suitable to tractor-

implement coupling. follow all

directions of the operation manual,

concerning both the fastening ac-

cording to connection direction and

safety rules to avoid rotation of

protections (chains) and overlaying

of the telescopic tubes. also keep

articulation angles.

WARNING

when a tractor with safety

frame is equipped with a front

loader, there is still a risk if the

implement is improperly used.

This risk is due to objects fall-

ing from above. The operator

has no protection against this

risk.

•

M46-EU,AU-EEC인증용-01.indd 24

2017-03-10 오전 8:14:40

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды