Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 100 / 192

CS2610

Check.if.the.seat.is.securely.

locked.after.the.seat.adjust-

ment.

Do.not.adjust.the.seat.while.

driving..The.seat.may.move.

suddenly.causing.the.loss.of.

control.of.the.tractor.

•

WARNING

1. Adjust the seat and fasten the seat

belt.

M46O504A

(1) Seat

(2) Seat Adjustment lever (Sliding)

nect the clip to a part of the frame

without paint.

6. Start the engine of the tractor

with the charged battery.

7. Start the engine of the tractor

with the discharged battery.

8. Disconnect the black cable from

the negative battery terminals of

both of the tractors.

9. Disconnect the red cable.
10. Run the engine for at least 30

minutes to charge the discharged

battery.

11. If the battery is discharged again,

replace it or check the charging

system, such as the alternator.

OPERATING.THE.TRACTOR

DRIvING

1. Check that the voltage of the dis-

charged battery is same as the

voltage of the other tractor or ve-

hicle for jump start. (Specification

for this tractor: 12v)

2. Check the length of the jump cable

and position another tractor near

the tractor with the discharged bat-

tery. Then, put all the shift levers

in the neutral position, apply the

parking brake, and stop the en-

gine.

3. Wear protective glasses and

gloves and open the hoods of both

tractors. Remove the battery termi-

nal cover as necessary.

4. Connect the alligator clips on both

ends of the red positive cable to

the positive terminals of both bat-

teries.

5. Connect one clip of the black neg-

ative cable to the negative terminal

of the normal battery and the other

clip to the tractor body with the dis-

charged battery. make sure to con-

M46-EU,AU-EEC인증용-05.indd 10

2017-03-10 오전 8:27:34

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды