Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 33 / 192

safetY precautions

H11O107a

C56O185a

ROPS (Roll Over Protective

Structure), sun canopy or

cabin are not a FOPS. (Falling

Object Protective Structure)

It never can protect the riders

against falling objects.

Avoid driving the vehicle into

a dangerous area such as fall-

ing rocks zone.

•

ImPORTANT

ImPlEmENTS ANd ATTAChmENTS

WARNING

Use exclusively front loader

approved by the tractor's man-

ufacturer, with CE mark and

parallelogram type.

The installation and modifica-

tion of the tractor must be car-

ried out with the highest tech-

nical standards by specialised

workshops with qualified per-

sonnel. Such workshops must

be able to guarantee and at-

test the risk analysis provided

for in the machinery directive

2006/42/EC concerning the

foreseen and predictable use

of the tractor with front loader,

in order to carry out all re-

quired adaptations of the trac-

tor.

Use the front loader and all

supplied equipment as pre-

scribed by the loader's opera-

tor manual.

•

Keep the loader's operation

manual together with the trac-

tor's manual, always at hand

in the storage compartment of

the tractor.
before driving or operation

your tractor, it is mandatory

to read this manual very care-

fully, with special attention to

the chapter concerning safety

rules.

•

ImPORTANT

M46-EU,AU-EEC인증용-01.indd 23

2017-03-10 오전 8:14:39

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды