Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 83 / 192

desCrIpTION OF OperATING sysTeM

M46O440A

M46O439A

Turning the lever counterclockwise

increases the lowering speed while

turning it clockwise decreases the

lowering speed. Also, turning it clock-

wise to its end can fix the implement

to a certain position.

(1) Lowering speed control lever

(A) high speed

(b) Low speed

lIFTING ARM (lOwER lINK)

SPEED CONTROl lEvER

DOublE ACTING lEvER (OPTIONAl)

(1) double Acting Lever

(A) port A

(b) port b

This lever is used to control a auxil-

iary hydraulic implement installed on

rear.
Lowering the lever supplies hydraulic

fluid to port b, while raising it sup-

plies hydraulic fluid to Port A.

pushing the lever supplies the port A

with hydraulic pressure while pulling

it supplies the port b with hydraulic

pressure.
For detailed information, see "Opera-

tion" in Chapter 5.

M46O448A

(1) Quick Coupler

Put the detent valve operating

lever into the neutral position

when the hydraulic implement

is not in use. If the detent valve

is kept in the operating position

for an extended period of time,

the relief valve is kept open and

the temperature of the hydraulic

fluid rises, leading to damage

of various hydraulic parts, such

as the oil seals and O-rings.

•

wARNING

This lever does not control the

lifting speed of the lifting arm.

•

NOTE

M46-EU,AU-EEC인증용-04.indd 25

2017-06-16 오후 1:07:06

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды