Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 182 / 192

CS2610

TracTor TroublEshooTing

causE

counTErMEasurEs

1. When tractor does not

move while engine is run

ning

•

Shift lever is in neutral position

•

Check the shift levers.

•

Parking brake is applied

•

Release the parking brake.

2. Brake is not operating

properly

•

Brake does not operate or only

one brake pedal operates

•

The brake pedal play is excessive. Adjust the play.

•

The brake lining is worn or stuck. Have it replaced in a work

shop.

•

Brake pedal does not return

properly

•

The brake return spring is damaged. Replace it.

•

Grease is insufficient on each mating surface.

Remove rust and apply grease.

3. Steering wheel is not

operating properly

•

Steering wheel is heavy or vi

brate

•

The toe-in is incorrect. Adjust it again.

•

The tire inflation pressure is different. Inflate the left and right

tires into the specified pressure.

•

Each connection is loose. Re-tighten each connection and

replace the part.

•

Steering wheel play is excessive

•

The steering wheel shaft is worn. Have it repaired in a work

shop.

•

Metal parts are worn. Have them repaired in a workshop.

•

Each connection has play. Tighten the connection again.

M46-EU,AU-EEC인증용-09.indd 4

2017-03-10 오전 8:51:15

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды