Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 137 / 192

maintenance

MAINTENANCE ChECk lIsT

DAIly ChECk ChART

※

for detailed information about maintenance codes, refer to the corresponding section in each chapter.

sERVICE sChEDUlE

MAINTENANCE

CODEs

ITEM

sERVICE REQUIRED

engine oil

Check the oil level and add needed. Do not overfill

Hydraulic (Trans / Diff) fluid

check level and add as needed

Engine air filter and air system

check condition indicator (if equipped)

check for leaks and damaged components. Do not use compressed air to

clean elements

engine cooling system

clean debris from oil cooler, radiator, screen and grills

check coolant level cold, add premixed coolant as needed

f, g, ah

seat belt

check the condition of seat belt and mounting hardware. repair or replace as

needed

tires

check for wear, damaged tires and ensure for proper sized tires and correct air

pressure

parking brake

check operation and have dealer adjust if required

clean pedal

clean brake pedal, travel control pedal

general items

check for loose or broken parts, damaged operator cab, instrument operation,

loose wheel nuts / bolts, oil leaks and damaged or missing signs (decals)

Replace floor mat if damaged or missing

q, ag, ah, am

pto

inspect the splines. replaced damaged or missing shields and guards

three-point linkage

check operation and condition of pins, links and bars

implements (if equipped)

check mounting hardware for loose or broken parts

M46-EU,AU-EEC인증용-07.indd 3

2017-04-25 오후 4:59:54

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды