Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 184 / 192

CS2610

causE

counTErMEasurEs

5. Electric system is faulty

•

Battery cannot be charged

•

Check the battery and alternator.

•

Horn does not sound

•

The horn switch is faulty. Replace or see

KioTi

dealer.

•

The wiring is faulty. Replace or See

KioTi

dealer.

•

The horn is damaged. Repair or replace it.

•

Turn signal lamps do not blink

•

The bulb is blown. Replace it.

•

The blinking device is faulty. Repair or replace it.

•

The ground and terminal wirings are poorly contacted.

Check and clean them.

•

Work lamps do not come on

•

The bulb is blown. Replace it.

•

The ground and terminal wirings are poorly contacted.

Check and clean them.

※

If you do not find the cause of trouble, consult your dealer for assistance.

M46-EU,AU-EEC인증용-09.indd 6

2017-03-10 오전 8:51:15

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды