Daedong KIOTI CS2610 Скачать руководство пользователя

Страница: 131 / 192

3-POINT hITch IMPLEMENT OPERATION

1. up and down of boom
Pulling the joystick lever back (b)

lifts the boom of the loader while

pushing it forward (A) lowers the

loader boom.

(A) boom down

(b) boom up

2. Roll back & dump
"Roll back" means that the bucket

scoops up. To operate this func-

tion, move the joystick lever to

the left (A) "dump" means that

the bucket dumps. To operate this

function, move the joystick lever to

the right (b)

(A) bucket Roll back (b) bucket dump

3. float
The floating function is activated

when the joystick lever is pushed

one position further from the down

position. When the lever is in this

position, the boom moves up and

down freely along the surface of

the ground as the hydraulic line is

opened from the valve to the boom

cylinder. This function is useful

when removing soft objects on

hard ground. (For example, when

removing snow or sand on an

paved road or removing night soil

on the ground in a stall)

M46O608A

M46O609A

If moving the lever to the float

ing position while the boom is

up in the air, the boom can fall

freely and lead to an accident.

•

WARNINg

4. fast dump
The fast dump function is activated

when the joystick lever is pushed

one position further to the right

from the dump position.

M46-EU,AU-EEC인증용-06.indd 15

2017-04-26 오전 11:42:01

Содержание KIOTI CS2610

































































































































































































Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды

Daedong KIOTI CS2610, Руководство пользователя

Результаты поиска

Содержание KIOTI CS2610

Отзывы:

Похожие инструкции для KIOTI CS2610

Бренды по названию

Популярные бренды